A Comprehensive Analysis Of The Plastic Processing Technology For Titanium Alloy Sheets, Strips, And Foils

Feb 02, 2026 Leave a message

I. Theoretical Basis and Technological Characteristics of Titanium Alloy Plastic Processing

1. Common Principles of Metal Plastic Processing The essence of titanium alloy plastic processing is to utilize the plastic deformation capacity of solid metals to change their microstructure through external force, ultimately obtaining titanium materials with the desired shape and properties. This process follows the classical theory of metal plastic processing, including:

• Stress-strain relationship: The flow stress of titanium alloys exhibits a non-linear relationship with deformation temperature and strain rate;

• Recrystallization mechanism: Dynamic recrystallization is key to refining grains and improving plasticity;

• Friction and lubrication: The coefficient of friction during rolling directly affects the quality of the sheet shape. Technical consensus: Titanium alloy processing requires a balance between temperature, deformation amount, and oxidation control to avoid the generation of coarse grains and surface defects.

2. Unique Challenges of Titanium Alloys Compared to traditional metals such as steel, copper, and aluminum, the processing difficulty of titanium alloys lies in:

• High deformation resistance: The yield strength of pure titanium is three times that of aluminum, and the work hardening rate of titanium alloys (such as GR5) is up to twice that of steel;

• Narrow plasticity window: Pure titanium has poor plasticity at room temperature and requires warm rolling at 200-450℃ or hot rolling at above 800℃ to obtain good formability;

• Sensitive to high-temperature oxidation: Titanium oxidizes rapidly above 600℃, forming a hard and brittle oxide layer (TiO₂), increasing the difficulty of subsequent processing;

• Strong tendency to absorb gases: It easily absorbs interstitial elements such as hydrogen and oxygen during heating or pickling, leading to "hydrogen embrittlement" or "oxygen embrittlement." Case study: In the production of aerospace sheet metal, an error in heating temperature control resulted in an excessive oxide layer thickness, ultimately causing the entire batch of sheet metal to be scrapped, resulting in losses of several million yuan.

Titanium alloy foil

 

II. Core Process Flow for Titanium Alloy Plate, Strip, and Foil Production

1. Slab Preparation and Pretreatment

• Raw Material Selection: High-purity titanium ingots prepared using VAR (Vacuum Arsenic Arc Refining) or EB (Electron Beam Refining) processes, with impurity content ≤0.1%;

• Surface Treatment: Removing surface defects (such as cracks and inclusions) from the ingot by sandblasting or turning to prevent crack propagation during processing;

• Dimensional Control: Designing the slab thickness according to the finished product specifications; hot-rolled slab thickness is typically 150-300mm. Standard Requirements: Slab surface roughness Ra≤3.2μm to ensure subsequent rolling stability.

2. Heating Process Control

• Hot Rolling Heating:

• Segmented Heating Method: First, heat to 600℃ at a rate of ≤50℃/h, hold for 2 hours, then rapidly heat to 950-1050℃ (α+β phase region);

• Atmosphere Protection: Introduce argon gas or use vacuum heating in the electric heating furnace to reduce the oxidation rate;

• Temperature Uniformity: Monitor in real time with an infrared thermometer, temperature deviation ≤±10℃.

• Warm Rolling Heating: Controlled at 650-750℃, oxide layer thickness ≤2μm, can be directly removed by pickling. Key Parameters: Heating temperature deviation must be controlled within ±10℃ to avoid local overheating leading to grain coarsening.

3. Rolling process design

(1) Hot rolling process

• Initial rolling temperature: 980-1020℃, final rolling temperature ≥850℃;

• Reduction per pass: first pass reduction ≤15%, subsequent passes gradually increase to 30%-40%;

• Grain control: final pass deformation is completed in the α phase region (≤882℃), refining the grain to ASTM 8-10 grade;

• Shape control: hydraulic bending roll system is used to control residual stress ≤50MPa.

(2) Warm rolling process

• Temperature range: 600-700℃, utilizing the dynamic recrystallization characteristics of titanium to improve plasticity;

• Oxide layer control: post-rolling oxide layer thickness ≤2μm, which can be directly removed by pickling;

• Pass planning: single pass reduction ≤8%, total deformation ≤30%, avoiding edge cracking. Advantages: warm rolling can omit the intermediate annealing process, shortening the production cycle by more than 20%.

(3) Cold rolling process

• Multi-pass design: 0.3-1.8mm thin plates need to be cold rolled in 5-8 passes, with the deformation amount controlled at 10%-15% per pass;

• Intermediate annealing: Vacuum annealing (650℃/2h) is performed when the cumulative deformation amount reaches 30% to eliminate work hardening;

• Surface quality: Roll coating lubrication technology is adopted to reduce scratch defects. High alloy material treatment: For α+β type alloys such as Ti-6Al-4V, the deformation amount per pass needs to be reduced to 5%-8% to prevent edge cracking.

4. Finishing and post-treatment

• Pickling process:

• Two-step method: First, the oxide layer is removed by a mixture of 10%HF + 30%HNO₃ acid, and then passivated with 5% citric acid;

• Environmentally friendly alternative: Develop a fluorine-free pickling process to reduce the amount of hydrofluoric acid used by more than 80%.

• Straightening Process: Residual stress is eliminated using a ten-roll straightener, achieving a straightness ≤1mm/m;
• Surface Inspection: Subcutaneous defects are detected using an eddy current flaw detector to ensure the absence of cracks, inclusions, and other defects.

 

Titanium alloy sheet, strip and foil

 

III. Process Optimization Directions and Industry Trends
1. Near-Net-Shape Forming Technology: Developing precision rolling technology to reduce machining allowances from the traditional 3mm to within 0.5mm;
2. Intelligent Control: Introducing digital twin technology to monitor rolling force, temperature field, and other parameters in real time, enabling adaptive process adjustment;
3. Green Manufacturing: Promoting fluorine-free pickling processes to reduce environmental pollution risks;
4. Composite Processing: Exploring laser-rolling composite forming technology to break through the room temperature forming limits of titanium alloys;
5. Superplastic Forming: Achieving superplasticity of titanium alloys at 850-950℃ through microstructure control for integrated forming of complex structural parts.